How To Keep Bathroom Plumbing In Good Working Order

Owning your own place ought to be certainly one of that which causes you to ready to fight on earth since it’s such an enormous accomplishment. Unfortunately, you usually end up being nervous about everything, especially your bathroom plumbing.

A few of you would possibly wonder what’s so problematic concerning the plumbing in the toilet when compared to rest of the house. Well, it really is related to the standard “life functions” that happen in the bathroom. The very last thing the plumbing in that room needs to have is a problem because the last thing we would like in your home is stuff in the plumbing.

The Toilet

The problem that a lot of house owners have is that they are not very experienced when it comes to working on the plumbing in their house, whatever the room. When it comes to the toilet, we have fairly rudimentary knowledge of how to use a plunger, but behind our minds, we actually don’t need to work that prospective mess. Still, you’re a home-owner now, which means you really have to be in addition to things. Your house is dependent upon your elbow grease to keep doing its thing, so an adequate amount of sticking your head in the ground – it is time to get to work.

Here are a few simple tips on keeping your bathroom plumbing working properly:

Always Be On The Lookout For Drips & Leaks – Listen to your toilet after you flush and observe your faucet after you’ve washed your hands. Do you hear or see drips? In that case, you’re seeing two things: 1) a symptom of one that has to be fixed; and 2) money through drain. You would be shocked to figure out how much water is wasted due to small leaks.

Try To Prevent Clogs and Blockages – Most clogs and blockages in your bathroom drains are caused by greasy build-up, hair, and other yucky stuff. Try best to reduce how much this affects you by using hair traps.

Check Fixtures for Cracks and Leaks – So, you’re a beginner plumber, but of course that doesn’t mean you can’t see one that isn’t quite right. Have a flashlight and look your bathroom fixtures for any developing cracks and leaks. The compromise of the actual fixture can interrupt the essential part of your plumbing.

Be Proactive – In case there is the same place to be slightly over the top in terms of trying to get ahead of things, it is your bathroom. Discover when you have hard water. Check out limescale. In case you are in older home, take into consideration upgrading the vanity plumbing. Provide your bathroom every chance it can have to run well.

Your Peace of Mind

Your bathroom plumbing doesn’t have to be a menace to your peace of mind. In spite of little to no understanding of plumbing, you could in fact do a lot to keep a bathroom plumbing operating the way it should. In case that an issue should occur, be proactive and seek out a local plumber develop a stellar reputation & great service. Having a knowledgeable plumber on your side is always a good bet.

For those of you living in downtown Vancouver you can always call these guys.

Pioneer Plumbing & Heating
Downtown Division
Phone: (778) 839-2040
1101-1202 Harwood St
Vancouver BC, V6E 1S3

How To Install A Toilet Yourself

In this article we look at what’s involved in replacing a toilet by yourself. There are a few things to think about before starting, one of those being the awkwardness and weight of the toilet. If you have trouble lifting heavy objects then this is probably not a job you want to tackle alone. Get someone with a good back to help lift and position the toilet when removing and alps for fitting the new one into place. Typical reason for doing this are things like a cracked bowl, excessive water usage in the flush, or just plain too old.

Another problem is the constantly annoying clogged toilet Kelowna. It’s not really a reason to install a new toilet, but it can add to the frustration and help make the decision to install a new one. One more thin to consider. If you find yourself in a bind at any point in the procedure, we suggest you get a local Kelowna plumber to do it for you. It’s really not that expensive for something as straight forward as a toilet installation, but with most DIY projects, things tend to go wrong more often than not.

Step one: Get the tools you will need

To replace a toilet you will need just a few tools. You will need either an adjustable wrench or a standard wrench set with different sizes. You will also need a razor knife and some towels for cleanup.

Step Two: Materials

The most obvious will be the toilet itself. The brand and model of toilet will depend on your taste and budget. However, when purchasing a toilet make sure to measure the distance between the mounting holes of the toilet tank and the wall. You will need to know the clearance you have; as many toilets have different size tanks. The other items you will need is a toilet bowl wax ring and toilet bowl mounting bolts. You may want to pick up a tube of silicone caulk as well.

Step Three: Removing the Old Toilet

First shut off the water supply to the toilet by turning the shut off valve located at the back of the toilet on the wall. Now flush the toilet several times to remove as much water from the bowl as possible. Remove the lid of the toilet tank and open the flapper valve to drain as much water out of the tank as possible and flush again. Now use a small cup or large towels to soak up any remaining water in the tank.

Next you will need to disconnect the water supply line. Use a standard wrench or adjustable wrench. If the supply line nut is made of plastic then use a pair of channel locks. If you are removing the entire toilet then you will not need to take the tank off the toilet bowl unless you want to for convenience of carrying it out.

If you are removing the tank, than do so by taking the nuts off the tank bolts located under and back of the toilet tank. If the nuts turn the bolt then you may need a screw driver on the bolt from the inside while turning the nut from below to break them free.

To remove the toilet bowl start by using the razor knife to cut away any caulk that is around the bowl. Removing the caulk will ensure you do not damage the floor when pulling up the toilet bowl and will make it much easier to do so.

Now take the two toilet mounting bolts off. They are located under the caps on both sides of the toilet base. In some cases these bolts can be rusted to the nuts and will not break free. If this is something you come across then use a small hacksaw blade to cut the bolt under the nut.

Now you can remove the toilet by gently rocking it from side to side, to break the seal the wax ring has made. Once the toilet is free simply pull straight up and out.

Step Four: Replacing the toilet

Prepare the area for the new toilet by cleaning the flange where the old wax ring was. Clean the floor of any debris and secure any loose flooring down. Set your new toilet mounting bolts in the slots provided on the floor flange. Tip the new toilet bowl on its side and gently press the new wax ring to make it stick to the toilet bowl.

Now carefully guide the toilet bowl over the mounting bolts in as straight downward motion as possible. Be careful not to damage the wax ring as you guide the toilet bowl in place. Now rock the toilet from side to side to set the wax ring in place and push the toilet bowl all the way down to meet the floor. Now place the nuts on the mounting bolts being careful to not over tighten as you can crack the porcelain very easily.

Step Five: Mounting the Toilet Tank

Follow the instructions supplied by the manufacturer on what seals to use between the tank and bowl. Guide the tank over the mounting holes and set the tank down. Now run the mounting bolts with any washers the manufacturer has included through the tank and place the nuts on the bottom. Tighten the nuts carefully, getting them snug but not too tight.

Be careful not to over tighten to prevent cracking the porcelain.

Now connect the supply line back to the underneath of the toilet. Open the supply line shut off valve slowly and let the toilet tank fill. Check for leaks all around the toilet as you do this. Once the tank is full, flush the toilet to ensure the wax ring sealed correctly.

You should not see any water coming from under the bowl. If you do you may have damaged the wax ring when placing the bowl down or did not set it correctly. If everything is working correctly all you have to do is caulk around the toilet bowl, put the tank lid on and the mounting bolt covers for the bowl.